AVR Programmer

AVR Programmer

Postby tannenba » Tue Dec 04, 2018 1:26 am

Following the instructions for firmware update on FG085, with the 07302 module, when I get to the read fuse bits and lock bits...the program fails. Setup as in picture and USBasp driver installed ok per Device manager. "No supported Programmer found". I have the FG085 powered up by it's own pwr supply and the jumper for pwr tar is off. Slo Clock is on. Did I get a bad programmer after all this wait? Does the programmer have to be programmed? If yes, how?
tannenba
 
Posts: 11
Joined: Sat Oct 27, 2018 8:18 pm

Re: AVR Programmer

Postby tannenba » Tue Dec 04, 2018 1:37 am

Found out it puts out the same error if the programmer is not attached to USB port. Seems it might be the USBasp driver? Tried more than one USB cable just to check.
tannenba
 
Posts: 11
Joined: Sat Oct 27, 2018 8:18 pm

Re: AVR Programmer

Postby tannenba » Tue Dec 04, 2018 2:39 am

Well, found Extreme burner doesn't recognize the programmer if Device manager lists it under USB devices, must be a lib-win32 device. now it finds the programmer, but doesn't recognize the chip to be programmed. (ATMEGA48 or ATMEGA168). Both LED's on the programmer are lit.

BTW the board ID on the 07302 (Lot 180508) is: CjzRa8b5

My ID for my 08503K FG085 (Lot 180412) is: tzGhs5b5

Rang out the cable and it is ok.
tannenba
 
Posts: 11
Joined: Sat Oct 27, 2018 8:18 pm

Re: AVR Programmer

Postby jye1 » Thu Dec 06, 2018 3:11 am

Please check if the devices have a suffix 'A'. That might make difference for some programming software.
jye1
 
Posts: 1191
Joined: Wed Feb 20, 2013 4:58 pm

Re: AVR Programmer

Postby tannenba » Fri Dec 07, 2018 10:35 pm

My unit has a MEGA48PA and MEGA168PA is that what you were asking? The board P/N is 109-08500-00P. Using the instructions from your webpage for the FG085,
Found link for extreme burner 1.4 and jumped thru the hoops to download it. It has a chip selection for a MEGA168/168v/168A. tried it for U5.
(read fuse bits/lock bits) and it still say incorrect chip. Looking like the 07302 is def?
tannenba
 
Posts: 11
Joined: Sat Oct 27, 2018 8:18 pm

Re: AVR Programmer

Postby jye1 » Mon Dec 10, 2018 1:27 am

Please try remove the file "libusb0.sys" from te eXtreme Burner folder.

You can also try this http://www.jyetech.com/Support/progisp172.rar .
jye1
 
Posts: 1191
Joined: Wed Feb 20, 2013 4:58 pm

Re: AVR Programmer

Postby tannenba » Mon Dec 10, 2018 1:29 am

Will try when time permits.

Thanks
tannenba
 
Posts: 11
Joined: Sat Oct 27, 2018 8:18 pm

Re: AVR Programmer

Postby tannenba » Tue Dec 11, 2018 1:17 am

Removing libusb0.sys did nothing. Don't know how to run progisp...It seems to be looking for a serial port (com port) this is USBasp on libusb-win32. Also all documents including readme are in Chinese which I cant read. Sorry.
tannenba
 
Posts: 11
Joined: Sat Oct 27, 2018 8:18 pm

Re: AVR Programmer

Postby tannenba » Tue Dec 18, 2018 9:09 pm

Any more suggestions/ideas? Possible the programmer is defective?
tannenba
 
Posts: 11
Joined: Sat Oct 27, 2018 8:18 pm

Re: AVR Programmer

Postby jye1 » Thu Dec 27, 2018 4:33 am

Please contact JYETech at jyetek@gmail.com. We're happy to send you another programmer for free so you can test out.
jye1
 
Posts: 1191
Joined: Wed Feb 20, 2013 4:58 pm

Next

Return to FG085

Who is online

Users browsing this forum: No registered users and 1 guest